← Knowledge Base
ApplicationsNovember 17, 2026 · 4 min read

How do you check fertilizer quality and detect discrepancies in its composition?

How do you check fertilizer quality? FAST, a rapid VIS–NIR screening test from ScanSpectrum, helps flag on site the samples that need laboratory analysis.

Fertilizer quality can be checked with a laboratory analysis, which compares the measured nutrient content against the manufacturer’s declaration. Initial checks can also be supported by screening tests based on VIS–NIR spectroscopy, which help identify samples that need a closer look.

At ScanSpectrum, we are developing FAST – the Fertilizer Adulteration Spectroscopy Test – for this purpose. It lets you take a measurement right where fertilizer is produced or sold and get preliminary information about possible quality discrepancies.

Why check fertilizer quality?

A fertilizer’s composition determines how much of each nutrient reaches the plants. If the actual content differs from what the label declares, the planned dose may not deliver the expected fertilization. That means a risk of extra costs, nutrient deficiencies and lower yields.

Discrepancies can result from deliberate adulteration, production errors or improper mixing of ingredients. Quality control helps catch such problems before the fertilizer is sold or applied in the field.

How does fertilizer testing with VIS–NIR spectroscopy work?

Spectral testing records a sample’s optical response in the visible and near-infrared range. The recorded spectrum is analyzed by a model developed for specific fertilizers and types of discrepancy.

In FAST, the measurement is taken with a portable ScanSpectrum spectrometer, and the user reads the result on a smartphone. The process has three steps:

  1. Take a fertilizer sample for testing.
  2. Run a spectral measurement with ScanSpectrum.
  3. Read the result, which helps you decide whether the sample needs further verification.

A granular fertilizer sample ready for measurement

The measurement requires no chemical reagents. What can be assessed depends on the scope of the analytical model and on the fertilizer types for which its performance has been verified.

How long does a rapid fertilizer test take?

In FAST trials in Nigeria, the whole process – from taking the sample to getting the result – took less than two minutes.

ScanSpectrum devices measuring fertilizer samples on a lab bench in Nigeria

This gave preliminary information about the tested fertilizer on site, without waiting for the sample to be transported to a lab. Samples flagged for verification can then be sent for detailed analysis.

What did fertilizer studies and tests in Nigeria show?

In a study QED carried out in Nigeria in 2025, all 35 samples analyzed showed discrepancies with quality requirements. This result applies to that specific group of samples and does not indicate the scale of the problem across the whole market.

As part of local ScanSpectrum trials, we scanned more than 600 fertilizer samples. Laboratory experts, agricultural advisors and students took part, which let us check how the measurements went and how people with different levels of experience handled the device.

FAST trial participants measuring fertilizers with ScanSpectrum

In November 2025, we presented FAST to representatives of fertilizer manufacturers, farmers’ organizations, and institutions that support and regulate the market in Nigeria. At meetings in Abuja and Kaduna, we discussed using rapid tests at fertilizer blending plants and distribution points. One of the needs raised was the ability to check the product right on site.

Does screening replace laboratory analysis?

Screening helps identify samples that need closer checking. Laboratory analysis, on the other hand, is used to confirm the composition and explain the discrepancies detected.

A FAST result is not in itself proof of deliberate fertilizer adulteration. A detected deviation needs verification, since it may also stem from a production error or from the product not being uniform.

Combining rapid on-site checks with laboratory analyses can make it easier to choose samples for further testing and to check deliveries more often.

At which stages of the supply chain should fertilizer quality be checked?

Quality control is needed at each stage of a fertilizer’s journey from the manufacturer to the farm. We are developing FAST with three uses in mind:

  • In production and blending plants – for preliminary checks of batches before shipment.
  • In distribution and retail – to catch products that need further verification.
  • In the work of agricultural advisors – to get additional information before a fertilizer is bought or applied.

Detecting discrepancies early means a sample can be sent for detailed testing before the fertilizer reaches the field.

Want to build a model for your material?

We run the calibration together with the client: from choosing reference samples to a ready-to-use model in the app.

contact@scanspectrum.ai →